ACTIONTEC ELECTRONICS, INC. FME288 Card Type Fax, Modem (synchronous/asynchronous), Network Interface Card Chip Set Unidentified I/O Options Ethernet 10BaseT connector NIC Type Ethernet Network Transfer Rate 10Mbps Maximum Modem Rate 28.8Kbps Maximum Fax Rate 14.4Kbps Data Bus PCMCIA Type II Fax Class Class I & II Data Modulation Protocol Bell 103/212A ITU-T V.21, V.22, V.22bis, V.23, V.25bis, V.32, V.32bis, V.34 Fax Modulation Protocol ITU-T V.17, V.21CH2, V.27ter, V.29 Error Correction/Compression MNP5, MNP10, V.42, V.42bis Topology Star Wiring Type Unshielded twisted pair Boot ROM Not available V2286 Proprietary AT Command Set AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD Type: Configuration Format: AT [cmds] %En [cmds] Description: Controls auto-retrain mode and fallback/fall-forward Command Function %E0 Auto-retrain disabled %E1 Auto-retrain enabled %E2 Auto-fallback/fall-forward enabled BIT MAPPED REGISTERS Register Default S28 Unidentified BIT-MAPPED REGISTER S14 Format: AT [cmds] S14=n [cmds] Default: 138 Range: 0-174 Unit: Bit-mapped Description: Controls echo, result codes and display, dial mode, and answer/originate mode. Bit Value Function 0 0 Not used 1 0 Command echo disabled 1 Command echo enabled 2 0 Result codes enabled 1 Result codes disabled 3 0 Display result codes in numeric format 1 Display result codes in verbose format 4 0 Not used 5 0 Tone dial enabled 1 Pulse dial enabled 6 0 Not used 7 0 Answer mode enabled 1 Originate mode enabled BIT-MAPPED REGISTER S21 Format AT [cmds] S21=n [cmds] Default: 4 Range: 0-253 Unit: Bit-mapped Description: Selects jack type, CTS/DCD/DSR signals, low DTR action, and the long space disconnect function Bit Value Function 0 0 Selects RJ-11, RJ-41S, or RJ45S jack 1 Selects RJ-12 or RJ-13 jack 1 0 Not used 2 0 CTS forced high 1 CTS follows RTS 4, 3 00 DTR signal ignored 01 Modem goes to command mode on low DTR 10 Modem disconnects on low DTR; Auto-Answer is disabled 11 Modem is initialized on low DTR 5 0 DCD forced high 1 DCD normal 6 0 DSR forced high 1 DSR normal 7 0 Long space disconnect function disabled 1 Long space disconnect function enabled BIT-MAPPED REGISTER S22 Format AT [cmds] S22=n [cmds] Default: 117 Range: 0-127 Unit: Bit-mapped Description: Controls speaker volume and controls, and limits results codes. Bit Value Function 1, 0 00 Volume off 01 Low level volume 10 Medium level volume 11 High level volume 3, 2 00 Speaker off 01 Speaker off on carrier 10 Speaker always on 11 Speaker on during handshake 6 - 4 000 Basic result codes only enabled 100 Basic and connection speed result codes enabled 101 Basic and connection speed result codes and dialtone detection enabled 110 All result codes except dialtone detection enabled 111 All result codes enabled BIT-MAPPED REGISTER S23 Format AT [cmds] S23=n [cmds] Default: 55 Range: 0-189 Unit: Bit-mapped Description: Grants/denies remote digital loopback, controls DTE rate and parity, and sets guard tone Bit Value Function 0 0 Remote digital loopback denied 1 Remote digital loopback allowed 3 - 1 000 Sets serial port speed to 0-300bps 001 Sets serial port speed to 600bps 010 Sets serial port speed to 1200bps 011 Sets serial port speed to 2400bps 100 Sets serial port speed to 4800bps 101 Sets serial port speed to 9600bps 110 Sets serial port speed to 19200bps 5, 4 00 Parity even 01 Not used 10 Parity odd 11 No parity 7, 6 00 Guard tone disabled 01 Guard tone disabled 10 Guard tone 1800Hz enabled BIT-MAPPED REGISTER S27 Format AT [cmds] S27=n [cmds] Default: 74 Range: 0-111 Unit: Bit-mapped Description: Selects synchronous/asynchronous mode, line type, clock source, and ITU-T/Bell modes. Bit Value Function 3, 1, 000 Asynchronous mode, serial port speed follows 0 connect speed 001 Asynchronous off-line command mode and synchronous 010 connect mode 011 Asynchronous off-line command mode; modem auto-dials first number in directory, then 100 synchronous connect mode 101 Asynchronous off-line command mode on low DTR, synchronous connect mode on high DTR 111 Auto-synchronous mode Error correction mode Buffered asynchronous mode 2 0 Switched line 1 Leased line 5, 4 00 Local modem generates transmit clock source 01 Local DTE generates transmit clock source 10 Remote DCE/DTE generates transmit clock source 6 0 ITU/T mode 1 Bell mode BIT-MAPPED REGISTER S31 Format: AT [cmds] S31=n [cmds] Default: 2 Range: 0-2 Description: Select automode Bit Value Function 0 0 Not used 1 0 Auto-mode detection disabled 1 In originate mode, handshake begins at line speed designated by the S37 register. Modem can shift to a slower speed if necessary. In answer mode, handshake attempted with the following protocols in order - V.32bis, V.32, V.22bis, V.22 or Bell 212, V.21, and Bell 103 BIT-MAPPED REGISTER S40 Format AT [cmds] S40=n [cmds] Default: 105 Range: 0-255 Unit: Bit-mapped Description: Controls MNP extended services, fallback, power level, break handling, and block size. Bit Value Function 0 0 MNP extended services disabled 1 MNP extended services enabled 1 0 MNP10 at 2400 and 1200bps disabled 1 MNP10 at 2400 and 1200bps enabled 2 0 Power level adjustment enabled 1 Power level adjustment disabled 5, 4, 3 000 \K0 001 \K1 010 \K2 011 \K3 100 \K4 101 \K5 7, 6 00 MNP block size is 64 characters 01 MNP block size is 128 characters 10 MNP block size is 192 characters 11 MNP block size is 256 characters BIT-MAPPED REGISTER S41 Format AT [cmds] S41=n [cmds] Default: Unidentified Range: 0-31 Unit: Bit-mapped Description: Selects compression, auto-retrain, flow control, and MNP mode. Bit Value Function 1 - 0 00 Data compression disabled 01 MNP5 enabled 10 V.42bis enabled 11 MNP5 and V.42bis enabled 6, 2 00 Auto-retrain disabled 01 Auto-retrain enabled 10 Auto-retrain and auto-fallback enabled 3 0 Flow control disabled 1 Flow control enabled 4 0 Stream mode for MNP 1 Block mode for MNP BIT-MAPPED REGISTER S201 Format: AT [cmds] S201=n [cmds] Default: 32 Range: 0-62 Description: Controls power level and compromise equalizer Bit Value Function 4 - 0 00000 Initial power level -26dBm 00001 Initial power level -30dBm 00010 Initial power level -10dBm ... ... 01010 Initial power level -10dBm 01011 Initial power level -11dBm ...to... ...to... 11110 Initial power level -30dBm 5 0 Equalizer disabled 1 Equalizer enabled BREAK SEND Type: Configuration Format: AT [cmds] \Bn [cmds] Default: 3 Range: 1-9 Unit: .1 second Description: Sends break to modem BREAK TYPE Type: Configuration Format: AT [cmds] \Kn [cmds] Description: Configures action of break signal Command Break from DTE Modem receives Break received \B from remote modem \K0 Online command Break sent to Buffers cleared, mode enabled, remote modem and break sent to DTE send no break buffers cleared to remote modem \K1 Break sent to Break sent to Buffers cleared, remote modem remote modem and break sent to DTE and buffers buffers cleared cleared \K2 Online command Send break to Break sent mode enabled, remote modem immediately to send no break immediately DTE to remote modem \K3 Send break to Send break to Break sent remote modem remote modem immediately to immediately immediately DTE \K4 Online command Send break with Break sent with mode enabled, transmitted data received data to send no break the DTE to remote modem \K5 Send break with Send break with Break sent with transmitted transmitted data received data to data the DTE COMPRESSION Type: Configuration Format: AT [cmds] %Cn [cmds] Description: Selects data compression Command Function %C0 Data compression disabled %C1 MNP5 enabled %C2 V.42bis enabled %C3 MNP5 and V.42bis enabled CONNECT MODE Type: Configuration Format: AT [cmds] \Nn [cmds] Description: Controls the type of connection the modem will operate in Command Function \N0 Normal mode enabled \N1 Direct mode enabled \N2 Reliable mode enabled \N3 Auto-reliable mode enabled \N4 V.42 reliable mode enabled \N5 MNP reliable mode enabled DIAL Type: Immediate Format: AT [cmds] D<#> [cmds] Description: Dials telephone number according to any modifiers included in the string Note: Any combination of modifiers can be used to produce the desired dial functions in sequence. Modifier Function J Link will be negotiated at highest possible speed K Power level adjustment enabled L Re-dial last number P Pulse dialing enabled R Accepted, but not acted upon S=n Dial stored telephone number n T Tone dialing enabled W Dialing resumed following dial tone detection ! Modem commanded to go off-hook for specified time before returning on-hook @ Wait for quiet answer , Dialing paused for amount of time specified in S8 register ; Modem returned to command state after dialing ^ Calling tone disabled > Generate a grounding pulse on ground output FLOW CONTROL Type: Configuration Format: AT [cmds] \Gn [cmds] Description: Selects modem port flow control Command Function \G0 Flow control disabled \G1 Flow control enabled FLOW CONTROL Type: Read-only Register Format AT [cmds] S39? [cmds] Description: Displays the current flow control Value Meaning 0 Flow control disabled 3 RTS/CTS flow control enabled 4 XON/XOFF flow control enabled 5 Transparent XON/XOFF flow control enabled 6 Both XON/XOFF and RTS/CTS flow control enabled FLOW CONTROL CHARACTER - XOFF Type: Register Format: AT [cmds] S33=n [cmds] Default: 19 Range: 0-255 Unit: ASCII Description: Sets the character used to represent XOFF FLOW CONTROL CHARACTER - XON Type: Register Format: AT [cmds] S32=n [cmds] Default: 17 Range: 0-255 Unit: ASCII Description: Sets the character used to represent XON LOCK SERIAL PORT Type: Configuration Format: AT [cmds] \Jn [cmds] Description: Sets operation of serial port speed Command Function \J0 Serial speed locked \J1 Serial speed follows connect speed MAXIMUM BLOCK SIZE FOR TRANSMISSION Type: Configuration Format: AT [cmds] \An [cmds] Description: Sets the maximum transmittable block size Command Function \A0 MNP block size is 64 characters \A1 MNP block size is 128 characters \A2 MNP block size is 192 characters \A3 MNP block size is 256 characters LINE SIGNAL LEVEL Type: Immediate Format: AT [cmds] %L [cmds] Default: Unidentified Range: 9-43 Unit: -1 dBm Description: Returns a value which indicates the received line signal level LINE SIGNAL QUALITY Type: Immediate Format: AT [cmds] %Q [cmds] Description: Returns a value which indicates line signal quality MNP - EXTENDED SERVICES Type: Configuration Format: AT [cmds] -Kn [cmds] Description: Selects MNP extended services Command Function -K0 MNP extended services disabled -K1 MNP extended services enabled MNP - STREAM/BLOCK MODE Type: Configuration Format: AT [cmds] \Ln [cmds] Description: Selects the transfer mode for MNP link Command Function \L0 Stream mode for MNP enabled \L1 Block mode for MNP enabled MNP10 - FALLBACK Type: Configuration Format: AT [cmds] -Qn [cmds] Description: Allows MNP10 to fall back to speeds slower than 4800bps Command Function -Q0 MNP10 at 2400 and 1200bps disabled -Q1 MNP10 at 2400 and 1200bps enabled MNP10 - LINK NEGOTIATION Type: Configuration Format: AT [cmds] *Hn [cmds] Description: Sets the speed at which MNP10 link negotiation will occur Command Function *H0 Link will be negotiated at highest possible speed *H1 Link will be negotiated at 1200bps *H2 Link will be negotiated at 4800bps MNP10 - POWER LEVEL ADJUST Type: Configuration Format: AT [cmds] )Mn [cmds] Description: Controls automatic transmit power level adjustment during MNP 10 link negotiation Command Function )M0 Power level adjustment disabled )M1 Power level adjustment enabled REPORT INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested Command Function I0 Reports product code I1 Reports OK I6 Reports modem data pump model and internal code revision TEST MODES Type: Register Format: AT [cmds] S16=n [cmds] Default: 0 Range: 0-125 Unit: Bit-mapped Description: Controls loopback tests: analog, digital, remote digital, and self tests Bit Value Function 0 0 Local analog loopback not in progress 1 Local analog loopback in progress 1 0 Not used 2 0 Local digital loopback not in progress 1 Local digital loopback in progress 3 0 Modem not in remote digital loopback 1 Remote digital loopback in progress 4 0 Remote digital loopback not requested 1 Remote digital loopback requested 5 0 Remote digital loopback w/ self-test not in progress 1 Remote digital loopback w/ self-test in progress 6 0 Local analog loopback w/ self-test not in progress 1 Local analog loopback w/ self-test in progress TEST MODE - PTT Type: Immediate Format: AT [cmds] %TTn [cmds] Description: Send PTT test signals for a line tests TRANSMISSION LEVEL - FAX Type: Register Format: AT [cmds] S92=n [cmds] Default: 10 Range: 0-15 Unit: -1 dBm Description: Sets the signal level for transmission while in fax mode TRANSMISSION LEVEL - LEASED-LINE Type: Register Format: AT [cmds] S99=n [cmds] Default: 10 Range: 0-15 Unit: -1 dBm Description: Sets the signal level for transmission over leased-lines TRANSMISSION LEVEL - PSTN Type Register Format AT [cmds] S91=n [cmds] Default 10 Range 0-15 Unit -1 dBm Description Sets the signal level for transmission over PSTN V.25bis COMMAND SET CONNECT INCOMING CALLS Type: Immediate Format: CIC Description: Instructs the modem to answer an incoming call; if no call is currently incoming, a result of INV will be returned. CALL REQUESTED NUMBER AND IDENTIFICATION Type: Immediate Format: CRI<#> Description: Adds dial string and identifier into memory. CALL REQUESTED NUMBER Type: Immediate Format: CRN<#> Description: Dials the number given; it will ignore spaces and hyphens in the string; if the string is more than fifty characters long, a result of INV will be returned. CALL REQUEST WITH ADDRESS Type: Immediate Format: CRSn Description: Dials the number stored in memory register n DISREGARD INCOMING CALL Type: Immediate Format: DIC Description: Instructs the modem to ignore the incoming call, if the modem is set to automatically answer; if no call is currently incoming, a result of INV will be returned. PROGRAM NUMBER Type: Configuration Format: PRNn or PRN Description: Stores a phone number in memory address n. If the second form of this command is issued (i.e. with no string to store), it will clear memory address n. REQUEST LIST OF DELAYED NUMBERS Type: Immediate Format: RLD Description: Requests the list of delayed numbers from the modem; this is a list of numbers that the modem attempted to call and failed, and is not allowed to call again until a set amount of time has elapsed; this is usually to prevent repeated dialing of a number (which could indicate an attempted security breach). REQUEST LIST OF FORBIDDEN NUMBERS Type: Immediate Format: RLF Description: Requests the list of forbidden numbers from the modem; the modem is unable to dial numbers on this list until its power has been cycled. REQUEST LISTED NUMBERS Type: Immediate Format: RLI Description: The modem will return VAL message. V.25BIS COMMAND SET RESULT CODES CALL FAILURE INDICATOR Type: Response Format: CFIxx Description: Indicates that the attempt to connect failed Response Name Description CFIAB Abort The call was aborted because either no dialtone was detected or a character was received from the host computer. CFICB DCE Busy An incoming call was detected after the dialing command was issued. CFIET Engaged Tone A busy signal was detected. CFIFC Forbidden The number given is on the Call forbidden list. CFINS Not Stored The memory address given did not contain a valid telephone number. CFINT No Tone The remote party did not issue a response tone. CFIRT Ring Tone A responding tone was detected, but the call timed out before it was completed. CONNECTION Type: Response Format: CNX Description: A connection has been successfully established DELAYED CALL Type: Response Format: DLCn Description: The telephone number given is on the delayed call list; the call cannot be completed until n minutes elapse. INCOMING CALL Type: Response Format: INC Description: An incoming call has been detected INVALID Type: Response Format: INV Description: The modem was issued an improper command VALID Type: Response Format: VAL Description: The command issued is valid and is being executed